Maintenance Matters - Guide to Transformer Inspection and Maintenance

Introduction

• Check the fan by operating it on Auto/Manual using the control switch

• Check and ensure that the fan rotates freely and at full speed within approximately 5 seconds

• They should rotate smoothly with minimal vibration

• Check to see if there are any defects

• Check for debris and scratch on the fan paint and physical defects

• Listen for noise as the fan runs

• If there is noise, check the bearings of the fan

• If the cooling system is equipped with the pumps as well then examine the pump valves for evidence of leaking around the gland seals

• Tighten the gland nut if necessary.

Gauges:

• Check the temperature gauge readings on the transformer and record them

• Check the ambient temperature and record it. Confirm that the temperature is within the normal operating temperature, but if it is normally high, carry out further investigations to find out why the high temperature

• Check the KVA or MVA load on the transformer and record it. Ensure that the transformer is not loaded beyond its capacity

• Check the oil level readings to ensure that there is no possible leak. If there are signs of a leak, carry out a pressure test. Transformer leaks must be repaired immediately to prevent further leaks, ingress of moisture and damage to the transformer

• When adding oil if needed, add only the same type of oil that is in the transformer

Paint Condition:

• Inspect the exterior paint for peeling, cracking, or corrosion

• Repaint as needed to protect against environmental factors

• Properly inspected and maintained transformer coating ensures an increased lifespan of a transformer as the tank metal will not be exposed to weather conditions for it to degrade, which could cause a leak of the oil

• Note the paint conditions as good, fair, or bad

 Bushing Terminals:

• If the transformer is energized and on load, check the temperature of the bushing using a thermal imager (e.g. Fluke TiX590 Infrared Camera). If the temperature reading is high, then there is a loose or dirty connection at the terminals

• If the transformer is not energized, use a torque measuring tool to make sure terminal connections are tight

• If connections are not tight, maintenance need will include cleaning, applying contact grease and tightening connectors

• Record your findings

Gaskets:

• Inspect visually gaskets for wear and tear, ensuring a proper seal

• Replace gaskets as necessary to prevent oil leakage

• When replacing a gasket, carefully clean mating surfaces to remove any rust, dirt, transformer oil, or other contamination that might prevent a good seal. Use an appropriate gasket cement when installing new gaskets

• Do not reuse old gaskets

• Six months after replacing a gasket, check and retighten if necessary

Rust Prevention:

During inspections, check all metallic parts of the transformer tank body for rust and degradation, starting from the tank to the radiator fins to the fans to the chassis and all parts of the tank body. Transformer should be regularly inspected for the rust.

Cover, Joints, and Bolts:

• Inspect the cover and joints for tightness and integrity

• Ensure that there is no rust on the bolts, joints, and the cover of the transformer

• In order to keep the rust away, make use of petroleum jelly to rub all over the bolts

• Check back every six months to see the condition of the bolts and joints, and if necessary, add more petroleum jelly on joints with little or no petroleum jelly left on them

Bushing and Surge Arrester Insulators:

• Bushings and surge arresters should be clean. If the surfaces are dirty, they should be cleaned while the transformer is not energized.

• Examine insulators for cracks or signs of electrical tracking and take necessary action

• Replace defective insulators if found to maintain insulation resistance

 Transformer Oil Level:

• Monitor transformer oil levels for the main tank and OLTC to ensure they remain within the recommended range. The transformer oil gauge is shown in Figure 6 and its location is shown in Figure 6.

• Top up oil as needed

 Control Wiring:

• The control wiring used to control the transformer should always be checked for functionality

• The control cabinet and associated conduit should be inspected to ensure that weather seals are intact.

• Inspect control wiring for damage or deterioration

• Replace or repair wiring as required to maintain operational control

 Oil Dielectric Test:

• It is advisable to annually test the dielectric strength of the transformer oil. To carry out the oil dielectric test on a transformer, oil samples should be drawn from the bottom of the tank

• It is important to make use of proper sampling and standard operating procedures to sample the oil from the transformer

• Conduct periodic oil dielectric tests to assess the condition of the insulating oil 

Silica gel Breather:

• During this breathing cycle, there is a need to prevent moisture from the atmosphere from entering the transformer, which can contaminate the oil inside and lead to a breakdown of the dielectric strength.

• Regularly check the breather by looking at its color

• A bright crystal with a blue tint shows that the silica gel is still fit for use, while a pink color shows that the breather has absorbed enough moisture and is due for a change 

On Load Tap Changer

• If the transformer is equipped with a load tap changer, inspect the tap changer for proper operation

• Detailed information for the inspection procedures and the frequency of inspection for the tap changer is usually supplied by the manufacturers

Conclusions

Maintaining transformers is crucial for ensuring their reliability and long lifespan as vital power system components. To achieve this, regular inspections and preventive actions in areas like cooling systems, monitoring oil levels and temperature, keeping the breather moisture-free, maintaining insulation, checking terminals for hot spot, and ensuring structural integrity are essential for peak performance. Adhering to maintenance guidelines discussed, allows power system to operate safely and efficiently, reducing downtime and costly repairs. In the end, a well-maintained transformer plays a significant role in strengthening the stability and resilience of our electrical networks, supporting the daily functioning of our society.

Courtesy :

Muhammad Hanif

Former Quality Manager, ABB Electrical Industries Co. Ltd., Riyadh, SA. Currently working with EPESOL Lahore, Pakistan as Senior Technical Manager.